
Thick Heat shrink tubing 22 to 6 mm X 10 cm
2 thick heat shrink sleeves, 10 cm long. Use diameter 22 to 6 mm (shrink ratio 4:1). Interior covered in a thermoplastic resin.
Heat shrink sleeves, 25 cm long. Use diameter 9 to 3 mm (shrink ratio 3:1). Interior covered in a thermoplastic resin.
If you are looking at a classic heat shrink tube such as can be found more or less everywhere you will without doubt be in for a surprise as the model chosen by DX Avenue has nothing in common, other than it is heat shrink.
Heat shrink sleeve containing a completely thermoplastic covered interior surface.
On heating, the diameter of the sleeve reduces by 3:1, and the interior resin melts. On cooling, the sleeve and the resin harden. This combination guarantees resistance to pullout and a perfect waterproofing for your connections, the whole preventing a sleeve from slipping. In the case of a connector mounted on a cable (coaxial for example), this sleeving ensures a reinforcement at the place where the cable is generally subject to stress when the radius of the curve is low (see photo above).
Characteristics
• Length: 25 cm
• Shrink diameter: 9 to 3 mm
• Shrink ratio: 3:1 (max)
• Wall thickness: about 0,7 mm
• Temperature range: -55°C to + 110°C
• Resistant to UV and corrosion: Yes
• Adhesive thermoplastic covering: Yes (over the whole interior surface)
• Dielectric resistance: 15KV/mm
• Packaging: 1 length of 40 cm in a sealed packet
Notes and Suggestions from DX AVENUE
• In contrast to our thick sleeves (which require a heat gun), a normal lighter is sufficient to shrink this sleeve, which facilitates its outdoor use.
• This sleeve cuts easily with a simple pair of scissors.
• To remove a sleeve, use a Stanley knife to cut it along its length (delicately if it covering a cable). The resin can be removed with thinners (white spirit, acetone...). However, if from the outset your connection is intended to be able to be removed, use instead a self amalgamating ribbon or waterproof mastic of the type we also sell. The heatshrink sleeve is primarily intended for a permanent installation.
2 thick heat shrink sleeves, 10 cm long. Use diameter 22 to 6 mm (shrink ratio 4:1). Interior covered in a thermoplastic resin.
2 thick heat shrink sleeves, 10 cm long. Use diameter 12 to 3 mm (shrink ratio 4:1). Interior covered in a thermoplastic resin.
Heat shrink sleeves, 25 cm long. Use diameter 18 to 6 mm (shrink ratio 3:1). Interior covered in a thermoplastic resin.
Mastic isolant 3M, caoutchouteux, auto-soudant, de couleur noir. Résistance à l'eau et à l'ozone. Souple, large et épais, il peut être étiré en fonction de l'application. Surface importante : 1,5 m X 38 mm, épaisseur 3,2 mm
Manchon thermorétractable épais, longueur 20 cm. Diamètre d'utilisation 56 à 17 mm (coefficient de rétreint 3:1). Intérieur revêtu d'une résine thermoplastique. Idéal pour réfection et protection de trappe ou self d'antenne.
Ruban auto-amalgamant (longueur 10 m) pour étancher, isoler et protéger contre l’humidité et la formation de rouille. Devient une masse homogène et résiste aux hautes tensions.
2 manchons thermorétractables épais, longueur 10 cm. Diamètre d'utilisation 22 à 6 mm (coefficient de rétreint 4:1). Intérieur revêtu d'une résine thermoplastique.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 35 mm. Embout tube entrant.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 25 mm. Embout tube entrant.
Mastic isolant, caoutchouteux, auto-soudant, de couleur noir. Résistance à l'eau et à l'ozone. Souple, large et épais, il peut être étiré en fonction de l'application. 1 m X 51 mm.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 45 mm. Embout tube entrant.
Gaine thermorétractable, longueur 25 cm. Diamètre d'utilisation 18 à 6 mm (coefficient de rétreint 3:1). Intérieur revêtu d'une résine thermoplastique.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 55 mm. Embout tube entrant.
2 manchons thermorétractables épais, longueur 10 cm. Diamètre d'utilisation 12 à 3 mm (coefficient de rétreint 4:1). Intérieur revêtu d'une résine thermoplastique.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 40 mm. Embout tube entrant.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 60 mm. Embout tube entrant.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 50 mm. Embout tube entrant.
Ruban adhésif PVC 25m x 19mm x 0,13mm, de qualité électrique, sans plomb, enduit d’une masse adhésive caoutchouc agressive qui permet notamment de l'étirer pour mieux l'appliquer. Température de service de -40ºC à +105ºC.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 20 mm. Embout tube entrant.
Ruban adhésif PVC 25m x 38mm x 0,13mm, de qualité électrique, enduit d’une masse adhésive caoutchouc agressive qui permet notamment de l'étirer pour mieux l'appliquer.
Bouchon plastique à ailettes pour tube rond diamètre extérieur 30 mm. Embout tube entrant.
Heat shrink sleeves, 25 cm long. Use diameter 9 to 3 mm (shrink ratio 3:1). Interior covered in a thermoplastic resin.