![Long Heat shrink tubing 22-6 mm Long Heat shrink tubing 22-6 mm](https://dxavenue.com/608-large_default/thick-heat-shrink-tubing-22-to-6-mm-x-10-cm.jpg)
Long Heat shrink tubing 12-3 mm
2 thick heat shrink sleeves, 10 cm long. Use diameter 12 to 3 mm (shrink ratio 4:1). Interior covered in a thermoplastic resin.
2 thick heat shrink sleeves, 10 cm long. Use diameter 22 to 6 mm (shrink ratio 4:1). Interior covered in a thermoplastic resin.
If you are looking at a classic heat shrink tube such as can be found more or less everywhere you will without doubt be in for a surprise as the model chosen by DX Avenue has nothing in common, other than it is heat shrink.
Thick heat shrink sleeve containing a completely thermoplastic covered interior surface.
On heating, the diameter of the sleeve reduces by 4:1, and the interior resin melts. On cooling, the sleeve and the resin harden. This combination guarantees resistance to pullout and a perfect waterproofing for your connections, the whole preventing a sleeve from slipping. In the case of a connector mounted on a cable (coaxial for example), this sleeving ensures a reinforcement at the place where the cable is generally subject to stress when the radius of the curve is low (see photo above) or the cable is suspended.
Characteristics
• Length: 10 cm
• Actual internal diameter: 24 mm
• Shrink diameter : 22 to 6 mm
• Shrink ratio: 4:1 (max)
• Wall thickness: from 1 to 2 mm (depending on shrinkage level)
• Temperature range: -40°C to + 120°C
• Resistant to UV and corrosion: Yes
• Adhesive thermoplastic covering: Yes (over the whole interior surface)
• Dielectric resistance IEC 243: >20KV/mm
• Packaging: 2 sleeves in a sealed packet
Notes and Suggestions from DX AVENUE
• To shrink this sleeve, use a classic hot air gun (heat stripper) which can be found at a reasonable price in store.
• If you overheat the sleeve slightly (heavy shrinking), it will happen that the sleeve will slip a little. That is simply due to the fact that the interior resin has melted. You have sufficient time to slide it into its proper place before the sleeving hardens.
• To remove a sleeve, use a Stanley knife to cut it along its length (delicately if it covering a cable). The resin can be removed with thinners (white spirit, acetone...). However, if from the outset your connection is intended to be able to be removed, use instead a self amalgamating ribbon or waterproof mastic of the type we also sell. The heatshrink sleeve is primarily intended for a permanent installation.
2 thick heat shrink sleeves, 10 cm long. Use diameter 12 to 3 mm (shrink ratio 4:1). Interior covered in a thermoplastic resin.
Heat shrink sleeves, 25 cm long. Use diameter 9 to 3 mm (shrink ratio 3:1). Interior covered in a thermoplastic resin.
Heat shrink sleeves, 40 cm long. Use diameter 18 to 6 mm (shrink ratio 3:1). Interior covered in a thermoplastic resin.
Gaine thermorétractable, longueur 40 cm. Diamètre d'utilisation 18 à 6 mm (coefficient de rétreint 3:1). Intérieur revêtu d'une résine thermoplastique.
Mastic isolant, caoutchouteux, auto-soudant, de couleur noir. Résistance à l'eau et à l'ozone. Souple, large et épais, il peut être étiré en fonction de l'application. 1 m X 51 mm.
Nettoyage, désoxydation, lubrification et protection sans dépôt des contacts électriques (y compris les connecteurs d'antennes). Grande contenance : 500 ml.
Ruban auto-amalgamant (longueur 10 m) pour étancher, isoler et protéger contre l’humidité et la formation de rouille. Devient une masse homogène et résiste aux hautes tensions.
Manchon thermorétractable épais, longueur 20 cm. Diamètre d'utilisation 56 à 17 mm (coefficient de rétreint 3:1). Intérieur revêtu d'une résine thermoplastique. Idéal pour réfection et protection de trappe ou self d'antenne.
Gaine thermorétractable, longueur 40 cm. Diamètre d'utilisation 9 à 3 mm (coefficient de rétreint 3:1). Intérieur revêtu d'une résine thermoplastique.
Mastic isolant 3M, caoutchouteux, auto-soudant, de couleur noir. Résistance à l'eau et à l'ozone. Souple, large et épais, il peut être étiré en fonction de l'application. Surface importante : 1,5 m X 38 mm, épaisseur 3,2 mm
Ruban adhésif PVC 25m x 19mm x 0,13mm, de qualité électrique, sans plomb, enduit d’une masse adhésive caoutchouc agressive qui permet notamment de l'étirer pour mieux l'appliquer. Température de service de -40ºC à +105ºC.
Ruban adhésif PVC 25m x 38mm x 0,13mm, de qualité électrique, enduit d’une masse adhésive caoutchouc agressive qui permet notamment de l'étirer pour mieux l'appliquer.
2 manchons thermorétractables épais, longueur 10 cm. Diamètre d'utilisation 12 à 3 mm (coefficient de rétreint 4:1). Intérieur revêtu d'une résine thermoplastique.
2 thick heat shrink sleeves, 10 cm long. Use diameter 22 to 6 mm (shrink ratio 4:1). Interior covered in a thermoplastic resin.